S.O.A.R – Icing


Category


Tags

Hey everyone, welcome to another S.O.A.R article! In this week’s article, we will be looking at icing, the hazards associated with it, and how pilots can prepare for and manage icing conditions both on the ground and in flight while flying on VATSIM.

Icing is a serious aviation weather hazard. Even relatively small amounts of ice can disrupt airflow over an aircraft’s wings and other critical surfaces, increasing drag, reducing lift, and affecting aircraft handling. Ice accumulates gradually, sometimes before pilots notice a significant change in performance.

Because of this, understanding how icing forms and recognizing when conditions are becoming unsafe are important parts of flight planning.

Understanding Icing

In-flight airframe icing generally occurs when an aircraft encounters supercooled liquid water droplets. These droplets remain liquid at temperatures below freezing but may freeze when they strike an aircraft surface.

There are three common types of airframe icing:

  • Rime Ice: Usually white or opaque, forming when smaller supercooled droplets freeze rapidly on contact.
  • Clear Ice: Often smooth or translucent, forming when larger droplets spread across a surface before freezing.
  • Mixed Ice: A combination of clear and rime ice.

Icing is commonly associated with temperatures below 0°C, but temperature alone does not determine the risk. Moisture, cloud conditions, and the presence of supercooled droplets must also be considered.

Freezing rain and freezing drizzle are particularly hazardous because larger droplets can accumulate beyond the areas protected by an aircraft’s ice protection systems.

Ground Icing and De-Icing

Icing hazards can begin before an aircraft leaves the gate. During winter operations, snow, frost, or freezing precipitation may accumulate on critical surfaces while an aircraft is parked or taxiing.

Even a thin layer of contamination can affect aircraft performance during takeoff. This is why operators follow the clean aircraft concept, which requires critical surfaces to be free of prohibited contamination before departure, subject to applicable aircraft-specific allowances.

Two procedures are commonly used:

  • De-icing: Removing existing ice, snow, or frost from aircraft surfaces.
  • Anti-icing: Preventing or delaying new contamination, often using specialized fluids.

Pilots may also encounter holdover time (HOT), an estimate of how long anti-icing fluid is expected to remain effective under specified weather conditions. It begins when the final anti-icing fluid application starts and depends on factors such as temperature, precipitation, and fluid type.

Holdover time is not a guarantee that an aircraft will remain free of contamination. If it is exceeded, a qualifying contamination inspection or further treatment may be required, depending on the applicable procedures and conditions.

On VATSIM, ground de-icing may be simulated through supported aircraft, scenery, or add-ons. Pilots should account for additional ground time and coordinate with ATC if de-icing affects their departure.

In-Flight Icing and Aircraft Protection

Once airborne, ice can accumulate on wings, tail surfaces, propellers, engine inlets, and exposed sensors. This can reduce climb performance, increase drag, affect instrument readings, and potentially lead to a loss of control.

Aircraft may use different systems to manage ice accumulation:

  • Anti-icing systems help prevent ice formation, often through electrical heating or hot engine bleed air.
  • – De-icing systems remove accumulated ice, such as pneumatic boots installed on some aircraft’s leading edges.

However, having ice protection equipment does not automatically mean an aircraft is certified for flight into known icing conditions. Even certified aircraft have operating limitations, and some icing conditions can exceed their protection capabilities.

Pilots should understand their aircraft’s procedures and limitations before encountering icing rather than assuming that activating an anti-ice system makes every condition safe.

Planning and Working With ATC

Avoiding hazardous icing begins before departure. Pilots should review available METARs, TAFs, SIGMETs, icing forecasts, and pilot reports, paying attention to freezing levels, cloud layers, and freezing precipitation.

An airport reporting temperatures above freezing does not necessarily mean the aircraft will avoid icing during its climb or descent.

If icing begins accumulating in flight, pilots should follow their aircraft’s procedures and identify a suitable way out of the conditions. This may involve changing altitude, requesting a different route, or diverting.

Climbing is not always the safest solution. Icing may extend above the aircraft, while ice accumulation may already be reducing climb performance. Descending toward warmer air may be an option, but terrain clearance, minimum altitudes, and the actual temperature profile must be considered.

On VATSIM, pilots should communicate early when icing requires a change to their clearance. For example:

1. Requesting an altitude change:

  • “Vancouver Centre, ACA123, encountering moderate icing, request descent to flight level 180.”
  • – “ACA123, request climb to flight level 240 to exit icing conditions.”

2. Requesting a different routing:

  • “Vancouver Centre, ACA123, request deviation right of track to avoid reported icing.”
  • “ACA123, unable to maintain current altitude due icing, request lower.”

3. Reporting icing conditions:

  • “Vancouver Centre, ACA123, reporting moderate rime icing at flight level 200.”

The exact wording does not need to be complicated. Pilots should explain what they are experiencing, how it affects the aircraft, and what assistance is needed.

ATC can assist with altitude changes, reroutes, and traffic separation, but controllers may not know which altitude offers better icing conditions. Responsibility for recognizing hazardous icing and requesting an appropriate course of action remains with the pilot.

If conditions become unsafe, pilots should communicate the urgency clearly and declare an emergency when necessary.

Common Icing Mistakes

One common mistake is assuming that icing only becomes dangerous after a large amount has accumulated. Even relatively small amounts of contamination can affect aircraft performance.

Another is relying too heavily on ice protection systems without understanding their limitations. On the ground, pilots should also avoid treating de-icing or holdover times as guarantees of a safe departure.

Finally, icing simulation varies between flight simulators and aircraft add-ons. Some reproduce ice accumulation and its effects in considerable detail, while others provide only limited simulation. Following realistic procedures remains good practice regardless of these differences.

Icing requires careful preparation, an understanding of aircraft limitations, and early decisions when conditions become unsuitable. Whether that means delaying departure, requesting a different altitude, or diverting, acting early gives pilots more options.

Plan ahead, understand your aircraft’s limitations, and never underestimate the effects of ice.